README web version of /home/usg/OPS/MTS/readme_xml/readme_78060002

Principal Investigator Email Address

```
matthew.lehnert@obspm.fr
```

Estimated Total Execution Time (hours, including overheads)

```
5hours
```

General Description

These are 2 high redshift galaxies for which we have SINFONI data for
 the emission lines, and now also are obtaining deep K-band images to trace the stellar
 population. The observations were begun during NACO-LGSF commissioning.

Please note that I have adjusted the seeing and airmass in jnps to force it to select
 the 7x7 lenslet array. However, I would be grateful if you could apply the seeing
 constrain given in the proposal (i.e. 0.8") to the actual observations.

Please also note that the tip-tilt star for the K20ID5 target is actually V=19mag
 (rather than the 17mag entered into jnps, which was done so that it could cmplete
 its optimisation). It was possible to use a star this faint during commissioning
 even though the loop gain/rate was low.

Waiver Requests

A waiver request to increase the length of the Obs up to 1.5 hours was
 submitted and approved (078.A-0600C.01.WAV)

Critical Observing Condition Constraints

Please bear in mind the seeing (0.8") constraint of the original proposal.
 The constraint set in jnps and transferred to p2pp was adjusted to force selection
 of the 7x7 lenslet array.

Time-Critical Aspects

The priority 1 target K20ID5 is at an RA of 3hrs:30 and so would need
 to be observed as soon as possible.

Special Execution Requirements

---(Empty)---

Special Calibration Information

---(Empty)---

ToO Information

---(Empty)---

ToO Activators List

---(Empty)---

Is this a Pre-imaging run ?

```
false
```

Pre-imaging Requirements

---(Empty)---

Source(s) of Pre-imaging

---(Empty)---

Pre-imaging sources not listed above

---(Empty)---

Do all your OBs comply with the instrument-specific requirements listed on the instrument-specific Phase 2 web page ?

If this is a pre-imaging run, did you select PRE-IMAGING for the Observing Category for each Observing Template ?

```
N/A
```

Do all your finding charts comply with both the general and instrument-specific Phase 2 Web Pages ?

If you submitted OBs for standard stars, did you specify the magnitude and spectral type of all standard stars in the OBs ?

```
N/A
```

Have you included OBs for any calibrations that you need but which are not part of the Calibration Plan ?

```
N/A
```

If you are observing Moving Targets, have you attached suitable ephemeris files to your OBs?

```
N/A
```

If you have preferences which OBs should be executed first, did you make use of the User Priority field in the OBs ?

If this is a run that requires coordinated observations with other facilities, did you give proper instructions in the Time-Critical Aspects Section ?

```
N/A
```

If you have PSF reference star OBs, do the names of those OBs begin with PSF_ ?

```
N/A
```

If there are Finding Charts attached to your OBs, is the field-of-view of at least one of these charts 2' x 2' (with clearly labelled field orientation) ?

Have you clearly marked and labelled your wavefront reference objects R1, R2, R3, ... (as specified in the NAOS Preparation Software) on your Finding Charts ?

Have you specified the magnitude of the brightest object in the field-of-view for each OB ?

Are there objects in any of your fields (including standard stars) which are brighter than the limits specified in the User Manual and on NACO web Pages ?

If the previous answer is yes, have you given a list of OBs and a justification for the brightness limit violation in the general description field ?

```
N/A
```

Last creation of page: Tue Oct 6 15:40:16 2009
If you have comments, please contact usd-help@eso.org