README web version of /home/usg/OPS/MTS/readme_xml/readme_77066900

Principal Investigator Email Address

• sofia@astro.lu.se

Estimated Total Execution Time (hours, including overheads)

• 69.9983333

General Description

• Highest resolution R~220000
  The central wavelength should be 869.4 nm.
  
  As the central wavelength is quite far out in the infrared we expect a lot
  of fringing pattern. In order to optimize the reductions and to minimize the residuals
  from this fringing we will observe fast rotating O/B stars. 
  
  All our primary targets have OB names WITHOUT an "_OBSTAR" extension.
  
  To each primary target we have assigned a fast rotating O/B star observing block.
   
  These observing blocks have the same name as the primary targets observing 
  blocks but WITH an "_OBSTAR" extension. These should be carried out directly
  before or after the primary target observing block. 
  
  For example:  the "T01_OBSTAR" observing block should be executed right before or
   
  right after the "T01" observing block.
  
  In a few cases we have multiple observing blocks for the same targets, e.g. "T07_1"
   and "T07_2". 
  If these should be scheduled for the same night it is not necessary to first observe
   "T07_1" then 
  "T07_1_OBSTAR" then "T07_2" and then "T07_2_OBSTAR". Instead you could just execute
   "T07_1" and 
  "T07_2" and once those are finished execute "T07_1_OBSTAR" and "T07_2_OBSTAR".

Waiver Requests

• Two waiver requests approved.
  
  1. All targets are bright => no finding charts
  
  2. For each primary target observing block we have assigned an observing block for
   a fast rotating O/B star.
     e.g. primary target observing block "T06" have a fast rotating O/B star observing
   block named "T06_OBSTAR"
     that should be executed right before or after the "T06". (see general description
   for details...)

Critical Observing Condition Constraints

• none

Time-Critical Aspects

• none

Special Execution Requirements

• The observing blocks whose names ends with "_OBSTAR" should be executed
   right before
  or after the primary observing blocks (i.e. those without the "_OBSTAR" extension),
   
  e.g. "T08_OBSTAR" should be executed right before or right after observing block
   "T08". 
  See general description for further details.....

Special Calibration Information

• ---(Empty)---

ToO Information

• ---(Empty)---

ToO Activators List

• ---(Empty)---

Is this a Pre-imaging run ?

• false

Pre-imaging Requirements

• ---(Empty)---

Source(s) of Pre-imaging

• ---(Empty)---

Pre-imaging sources not listed above

• ---(Empty)---

Do all your OBs comply with the instrument-specific requirements listed
 on the instrument-specific Phase 2 web page ?

• YES

If this is a pre-imaging run, did you select PRE-IMAGING for the Observing
 Category for each Observing Template ?

• N/A

Do all your finding charts comply with both the general and instrument-specific
 Phase 2 Web Pages ?

• N/A

If you submitted OBs for standard stars, did you specify the magnitude
 and spectral type of all standard stars in the OBs ?

• N/A

Have you included OBs for any calibrations that you need but which are
 not part of the Calibration Plan ?

• N/A

If you are observing Moving Targets, have you attached suitable ephemeris
 files to your OBs?

• N/A

If you have preferences which OBs should be executed first, did you make
 use of the User Priority field in the OBs ?

• N/A

If this is a run that requires coordinated observations with other facilities,
 did you give proper instructions in the Time-Critical Aspects Section ?

• N/A